Trane RAUJ-C20, Installation, Operation And Maintenance Manual

Page: 102 / 132

102 SS-SVX11K-EN
Zone Thermostat Checkout
(Honeywell T7067)
A Av va aiilla ab blle e O On nlly y F Fo orr 2 20 0 -- 6 60 0 T To on n U Un niittss
1. Open the system control switches 5S1 and 5S2 to
disable the Evaporator Fan and Heating system.
2. Close the main power disconnect switch and turn
control circuit switch 1S2, in unit control panel,
“ON”.
W WA AR RN NIIN NG G
L Liiv ve e E Elle eccttrriicca all C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o ffo ollllo ow w a allll e elle eccttrriicca all ssa affe etty y p prre ecca au uttiio on nss
w wh he en n e ex xp po osse ed d tto o lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
W Wh he en n iitt iiss n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e e elle eccttrriicca all
cco om mp po on ne en nttss,, h ha av ve e a a q qu ua alliiffiie ed d lliicce en nsse ed d e elle eccttrriicciia an n
o orr o otth he err iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n p prro op pe errlly y ttrra aiin ne ed d
iin n h ha an nd dlliin ng g lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss p pe errffo orrm m
tth he esse e tta asskkss..
3. At the Zone Thermostat (6U37), use a digital
voltmeter to verify that there is 20 volts DC power
between thermostat Terminals 1 & 2. See
illustration in Installation Electrical chapter,
Thermostat Wiring section for terminal
identification. Refer to
Table 29, p. 102 for the
thermostat “voltage output” ramps.
4. To check the “Cooling” output signal, place the
voltmeter leads between thermostat Terminals 1 &
4. Refer to illustration in Installation Electrical
chapter, Thermostat Wiring section and:
a. move the cooling (blue) setpoint lever from
right to left. As the cooling setpoint is lowered,
the voltage signal should increase and the
“Cooling” LED brighten.
b. move the cooling (blue) setpoint lever from left
to right. As the cooling setpoint rises, the
voltage signal should decrease and the
“Cooling” LED dim.
5. To check the “Heating” output signal, place the
voltmeter leads between thermostat Terminals 1 &
5. Refer to illustration in Installation Electrical
chapter, Thermostat Wiring section and:
a. move the heating (red) setpoint lever from left
to right. As the heating setpoint rises, the
voltage signal should increase and the
“Heating” LED brighten.
b. move the heating (red) setpoint lever form right
to left. As the heating setpoint lowers, the
voltage signal should decrease and the
“Heating” LED dim.
Table 29. Zone thermostat (6U37) “voltage output” ramps
1U11 Function
Nominal Operating Points and Throttling Ranges
Measured between
1U11 Terminals
Pull-In Voltage (a)
(VDC)
Drop-Out Voltage (a)
(VDC) Throttling Range
HEAT 1 (a) 4.63 4.0
Terminal 5 (heating) &
Terminal 1 (common)
HEAT 2 (a)
5.88 5.25
HEAT 3 (a)
7.13 6.50
HEAT 4 (a)Zone Thermostat
T7067
8.38 7.75
COOL 1 4.58 - 5.42 3.44 - 4.56
Terminal 4 (cooling) &
Terminal 1 (common)
COOL 2 5.43 - 6.34 4.69 - 5.81
COOL 3 6.63 - 7.63 5.90 - 7.10
COOL 4 7.84 - 8.92 7.11 - 8.39
Economizer 2.75 - 4.00
(a) "Pull-In" and "Drop-Out" values are ± 0.25 VDC
Discharge Air Sensor Checkout
(Honeywell 6RT1)
A Av va aiilla ab blle e O On nlly y F Fo orr 2 20 0 -- 6 60 0 T To on n U Un niittss
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
P Prre e--S Stta arrtt