Trane RAUJ-C20, Installation, Operation And Maintenance Manual

Page: 63 / 132

SS-SVX11K-EN 63
Wiring Requirements
Main Electrical Power Requirements
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
• Verify the power supply meets the required power
requirements of the system.
• Install power wiring in accordance with all
applicable codes.
• Install and connect properly sized power supply
wiring, with over current protection, to the main
power terminal block (1TB1) or to an optional
factory mounted non-fused disconnect switch (1S1)
in the control panel.
• Install and connect properly sized power supply
wiring, with over current protection, to the proper
termination point in the air handling unit (If
applicable).
• Install proper grounding wires to an earth ground.
• For EVP units only, install and connect properly
sized power supply wiring, with overcurrent
protection, to the proper termination point for the
chilled solution pump.
Field Installed Control Wiring
Requirements
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
115 Volt Control Wiring (All Units)
• Verify that the Control transformer (1T1) is wired for
the proper operating voltage.
• Connect properly sized wiring to the liquid line
solenoid valve(s).
• The phase monitor (1U3) when powered with line
voltage properly phased and balanced has a green
LED energized.
• Connect properly sized wiring to the hot gas bypass
solenoid valve(s), if applicable, to operate with the
unit. Refer to the unit wiring diagram that shipped
with the unit.
• Install the interlock circuitry wiring for the air
handling unit to permit compressor operation after
the fan has started, i.e., proof of fan operation
device, fan starter auxiliary contacts or pump
starter station, pump starter auxiliary contacts,
proof of flow device, etc. Refer to the field
connection diagram that shipped with the unit for
interlocking information.
• Install properly sized power supply wiring, with
over current protection, to the proper termination
point for the field provided economizer actuator(s),
if applicable. Refer to the “Economizer Actuator
Circuit” illustrated in the “Field Installed Control
Wiring” section.
“No Controls” Units
• A field provided “step” controller must be installed
and properly wired. (Controller will have 2, 4 or 6
steps, depending on unit configuration.) Refer to
the field connection diagram for connection
information.
• Install proper grounding wires to an earth ground.
• Install an outside air thermostat in series with the
flow switch to stop or prevent the unit from
operating below the recommended ambient
temperatures.
EVP Chiller Units
• Install proper grounding wires to an earth ground.
IIn nsstta alllla attiio on n E Elle eccttrriicca all