Trane RAUJ-C20, Installation, Operation And Maintenance Manual

Page: 100 / 132

100 SS-SVX11K-EN
W WA AR RN NIIN NG G
L Liiv ve e E Elle eccttrriicca all C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o ffo ollllo ow w a allll e elle eccttrriicca all ssa affe etty y p prre ecca au uttiio on nss
w wh he en n e ex xp po osse ed d tto o lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
W Wh he en n iitt iiss n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e e elle eccttrriicca all
cco om mp po on ne en nttss,, h ha av ve e a a q qu ua alliiffiie ed d lliicce en nsse ed d e elle eccttrriicciia an n
o orr o otth he err iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n p prro op pe errlly y ttrra aiin ne ed d
iin n h ha an nd dlliin ng g lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss p pe errffo orrm m
tth he esse e tta asskkss..
11. At the Chilled Water Controller, use a digital
voltmeter to verify there is 24 volts AC across
terminals TR & TR.
12. After approximately 15 seconds, the LEDs on the
W7100G should begin to illuminate as the cooling
outputs stage “On”.
13. Set the “Setpoint F” dial at 60ºF; within 15 seconds,
the LEDs should turn “Off” as the cooling outputs
stage “Off”.
14. Remove the 1780 ohm resistor from Terminals 6 &
7 and reinstall the wire jumper removed in step 6.
15. Set the “Setpoint F” dial at 50ºF; within 15 seconds,
the LEDs should turn “On” as the cooling outputs
stage “On”.
16. Turn the control circuit switch 1S2, in the unit
control panel, to the “OFF” position.
17. Remove the 3,400 ohm resistor from Terminals T &
T1 and reconnect the chilled water temperature
sensor leads to Terminals T & T1.
18. Remove the “Test Plug” from the W7100G test
socket and reinstall the red dust cover.
19. Plug the reset relay(s) 1K11 and 1k12 (if applicable)
back into their receptacle.
20. Turn the control switch 1S2 to the “On” position to
restore power to the control system.
Figure 71. W7100G chilled water controller
SETPOINT °F
RESET °F
CONTROL
BAND °F
Test Plug Socket
(Remove red dust cover)
ECONO
24 VAC
CHANGE
OVER
# STAGES
SENSOR
RESET
REMOTE
SETPOINT
SATELLITE
COOL
COOL
COOL
COOL
COOL
COOL
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
6
5
4
3
2
1
GND
TR
TR
W
R
B
Y
10
9
T
T1
8
7
6
P
P1
5
4
3
2
1
Chilled Water Sensor Checkout
(Honeywell Sensor)
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
1. Verify that the main power disconnect switch and
the control circuit switch 1S2, in the unit control
panel, is “OFF”.
2. At the temperature controller, disconnect the wire
connected to terminal T1. Use a digital ohmmeter
to measure the resistance across terminal T and the
wire removed from terminal T1.
3. Use the conversion chart in Figure 37 to convert the
measured resistance to an equivalent temperature.
4. Measure the actual temperature at the sensor
location. If the measured resistance in step 2 is not
within ± 10.0 ohms of the actual temperature, the
sensor is out of range; replace it.
P Prre e--S Stta arrtt