Toshiba Stratagy DK Installation & Programming Manual Download

Page: 4 / 84

Before You Start...

Is Strata DK ready?

Stratagy DK I&P R2 November 1998

Refer to the Stratagy Library CD-Rom for more details.

Is Strata DK
ready?

See the Strata DK
Installation /
Maintenance and
Programming
Manuals for details on
a specific Strata DK
product.

❐

Make sure Stratagy DK is compatible with your
Strata DK: It works with all DK280 (CPU
software release 2 and higher) and DK16
systems. It will also work with DK40/424.

❐

Always program Strata slot assignments

before

installing the Stratagy DK. Use these slot
assignments:

DK424:

use a universal slot, starting with slot

12 or 13 if an RSIU is in slot 11; never use
slots 27, 28, 31, 37, 38, 47, 48, 51, 57, 58,
67, 68, 71, 77, or 78.

DK280:

use any universal slot, starting with

slot 12; never use slots 11, 31 or 51.

DK40:

use any expansion cabinet slot.

DK16:

use any expansion cabinet slot.

❐

Be sure to set code 31 in Program 03 for the
slot where
Stratagy DK will be installed.

❐

All Strata DK’s

: if receiving Calling Party

Control (CPC) or Disconnect Clear from the
Exchange, use Program 15 to enable.

❐

Set Program 31 for Voice Mail operation on the
Strata DK ports connected to Stratagy DK.

❐

Always remember to

shut down

Stratagy

software

before

powering down Strata DK.

Note

DK40/424 release dates are still as yet to
be confirmed.

Is Strata DK’s
DTMF tone
detection
enabled?

❐

Strata DK needs to recognize Stratagy DK’s
DTMF signaling.

❐

Make sure an RRCS is installed in the DK424/
DK280, a K5RCU in the DK40, or a K4RCU3 in
the DK16.

❐

Run Program 03 and assign these code(s)
where the DTMF receiver is installed:

DK424/DK280

(RRCS installed on the

RCTU): code 92, 93, or 94 for the relevant
slots 00/01.

DK40

(K5RCU): code 98 for slot 00.

DK16

(K4RCU3): code 92 for slot 00

Summary of Contents for Stratagy DK





















































































Search results

Summary of Contents for Stratagy DK

Reviews:

Related manuals for Stratagy DK

Brands by name

Popular brands

Toshiba Stratagy DK, Installation & Programming Manual

Search results

Summary of Contents for Stratagy DK

Reviews:

Related manuals for Stratagy DK

Brands by name

Popular brands