Toshiba Stratagy DK Installation & Programming Manual Download | Manualshive

Page: 14 / 84

background image

Stratagy DK

Installation

1-6

Stratagy DK I&P R2 November 1998

Refer to the Stratagy Library CD-Rom for more details.

◆

Wear the anti-static wrist strap

included in the package. It can also be re-used so

should be left with the Strata DK cabinet. An electrostatic charge from your
body can damage the hard drive or other circuitry permanently.

◆

Hold the Stratagy DK by the edges or the strap

and never touch the board’s

surface. Pressure on the printed circuit board or contaminants from your
hands (e.g., skin oil, food particles, hand lotion) can cause component failure.

Step 1:

Read Through this Installation Guide First

Before starting the installation, read through these instructions thoroughly. Important
information is included in this Guide that is crucial to a successful installation.

Step 2:

Program the Strata DK

Note

The following instructions are based on the Stratagy DK being installed in a pre-
existing, or new installation of a Strata DK telephone system. If further information
is required around the Strata DK Programming, see the Programming section of the
relevant Strata DK Installation & Maintenance Manual.

To the Strata DK processor, the Stratagy DK functions as an analogue card (PSTU/RSTU).
Although there are some special program settings required for the Stratagy DK (e.g., DSS/
BLF feature), the Strata DK should be programmed just as it would for any external voice
mail system that is to be connected to it.

Important!

The Strata DK may need to be reset to initialise some Strata programming

assignments. It is important that you make all such assignments

before

installing the Stratagy DK.

1.

Using Program 03–Flexible PCB Slot Assignments set/verify the following slot
assignments:

◆

Set code 31 for the slot where Stratagy DK is installed (

see Step 4 “Install the

Stratagy DK” on Page 1-7

).

◆

Enable the Strata DK to receive DTMF signalling from the Stratagy DK:

◆

For DK424/DK280: Set codes 92, 93, or 94 (DK424 only) for slot 00 for the RRCS
installed on the RCTU.

◆

For DK40: Set code 98 for slot 00 for the K5RCU.

◆

For DK16: Set code 92 for slot 00 for the K4RCU3.

◆

Set code 64 for the slot where the PDKU resides. Stratagy DK will monitor this slot
for the DSS/Busy Lamp feature (

see “Busy Station Identification” on Page 1-5

).

Note

For DK16/40: slot 11 in the Base Cabinet must be set for code 64.

◆

If SMDI is desired with the Strata DK424/DK280: Set PIOU or PIOUS for code 43
or enable the SMDI port.

H

«
...
12
13
14
15
16
...
»

Summary of Contents for Stratagy DK





















































































Reviews:

No comments

Related manuals for Stratagy DK

Suite 64 Voice Flash

Brand: PCS Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands