Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 5 | Manualshive

Page: 5 / 220

Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 5

Notice to Users 3

Following information is for EU-member states only:

This product is marked according to the requirement in EU-Directive 2002/96/EC.
(Directive on Waste electrical and electronic equipment - WEEE)

The use of the symbol indicates that this product may not be disposed as unsorted municipal waste and
has to be collected separately. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of this product please contact your sup-
plier where you purchased the product.

«
...
3
4
5
6
7
...
»

Summary of Contents for e-studio 167





























































































































































































































Reviews:

No comments