manualshive.com logo in svg

Toshiba e-studio 167, Operator'S Manual For Copying Functions, Page: 207 / 220

Share
Download
Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 207

Specifications of Options    205

Paper Feed Pedestal

Drawer Module

TOSHIBA-recommended paper is used for the values above. Specifications and appearance are 
subject to change without notice in the interest of product improvement.

Model name

KD-1022

Acceptable paper size

A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP (A5, 
ST and non-standard size are not acceptable.)

Paper weight

64 - 80 g/m

2

Maximum capacity

550 sheets (80 g/m

2

)

Dimensions

623 mm (W) x 657 mm (D) x 367 mm (H)

Weight

Approx. 26.0 kg

Model name

MY-1028

Acceptable paper size

A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP (A5, 
ST and non-standard size are not acceptable.)

Paper weight

64 - 80 g/m

2

Maximum capacity

550 sheets (80 g/m

2

)

Weight

Approx. 4.0 kg

Summary of Contents for e-studio 167





























































































































































































































Reviews:

No comments