manualshive.com logo in svg

Toshiba e-studio 167, Operator'S Manual For Copying Functions, Page: 153 / 220

Share
Download
Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 153

Department Code    151

4

Press the [USER FUNCTIONS] button or 

 (copy mode) button.

The screen returns to the “copy mode” main screen.

Cancelling department management

Key in the master code in the department code entry screen, and then proceed to the following 
steps:

1

Press the [USER FUNCTIONS] button.

The “user functions mode” main screen is displayed.

2

Select “DEFAULT SETTINGS” with 

 and 

 buttons, and then 

press the [ENTER] button.

3

Select “GENERAL SETTING” with 

 and 

 buttons, and then 

press the [ENTER] button.

4

Select “DEPARTMENT CODE” with 

 and 

 buttons, and then 

press the [ENTER] button.

USER FUNCTIONS

1216

01.DEFAULT SETTINGS

02.LISTS

03.INITIAL SETUP

DEFAULT SETTINGS

01.GENERAL SETTING

02.COPY SETUP

03.FAX SETUP

GENERAL SETTING
04.WEEKLY TIMER
05.SPEAKER VOLUME

06.DEPARTMENT CODE

Summary of Contents for e-studio 167





























































































































































































































Reviews:

No comments