manualshive.com logo in svg

Toshiba e-studio 167, Operator'S Manual For Copying Functions, Page: 20 / 220

Share
Download
Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 20

18    General Precautions

General Precautions

When installing or moving

Warning

y

This equipment requires 220 to 240 V AC, 8 A 50/60 Hz electric power.
Do not use a power supply with a voltage other than that specified.
Avoid multiple connections in the same outlet. This could cause a fire or give you an electric 
shock. If you are considering increasing the number of outlets, contact an electrician.

y

Always connect this equipment to an outlet with an earth connection to avoid the danger of 
fire or electric shock in case of short-circuiting. Contact your service representative for the 
details. Be sure to use a 3-conductor, grounded wall outlet.
In areas, where a 2-pin plug is used, the equipment must be grounded for safety. Never 
ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.

y

Plug the power cable securely into the outlet. If it is not plugged in properly, it could heat up 
and cause a fire or give you an electric shock.

y

Do not damage, break or attempt to repair the power cable.
The following things should not be done to the power cable.

- Twisting it
- Bending it
- Pulling it
- Placing anything on it
- Making it hot
- Situating it near radiators or other heat sources

This could cause a fire or give you an electric shock. If the power cable is damaged, contact 
your service representative.

y

Do not install the equipment by yourself or try to move it once it has been installed. This 
could result in an injury or damage to the device. Contact your service representative if the 
equipment needs to be installed or moved.

y

Pull the plug out from the outlet more than once a year to clean around the prongs. Accumu-
lating dust and dirt could cause a fire due to the heat released by electric leakage.

Summary of Contents for e-studio 167





























































































































































































































Reviews:

No comments