Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 125

Page: 125 / 220

Paper Size Setting 123

Paper Size Setting

This section describes how to set the paper size placed in the drawer or on the bypass tray.

Press the [USER FUNCTIONS] button.

The “user functions mode” main screen is displayed.

Select “DEFAULT SETTINGS” with

and

buttons, and then

press the [ENTER] button.

Select “GENERAL SETTING” with

and

buttons, and then

press the [ENTER] button.

Select “DRAWER SIZE” with

and

buttons, and then press

the [ENTER] button.

USER FUNCTIONS

1216

01.DEFAULT SETTINGS

02.LISTS

03.INITIAL SETUP

DEFAULT SETTINGS

01.GENERAL SETTING

02.COPY SETUP

03.FAX SETUP

GENERAL SETTING

01.DRAWER SIZE

02.WALKUP SCREEN

03.TIMERS

Summary of Contents for e-studio 167





























































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Operator'S Manual For Copying Functions, Page: 125 / 220

Search results

Summary of Contents for e-studio 167

Reviews: