manualshive.com logo in svg

Toshiba e-studio 167, Operator'S Manual For Copying Functions, Page: 127 / 220

Share
Download
Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 127

Walkup Screen Setting    125

Walkup Screen Setting

This section describes how to set the screen when the power of the equipment is turned ON. In 
the initial screen set at the time of shipping, the "copy mode” main screen is displayed.

1

Press the [USER FUNCTIONS] button.

The “user functions mode” main screen is displayed.

2

Select “DEFAULT SETTINGS” with 

 and 

 buttons, and then 

press the [ENTER] button.

3

Select “GENERAL SETTING” with 

 and 

 buttons, and then 

press the [ENTER] button.

4

Select “WALKUP SCREEN” with 

 and 

 buttons, and then 

press the [ENTER] button.

USER FUNCTIONS

1216

01.DEFAULT SETTINGS

02.LISTS

03.INITIAL SETUP

DEFAULT SETTINGS

01.GENERAL SETTING

02.COPY SETUP

03.FAX SETUP

GENERAL SETTING
01.DRAWER SIZE

02.WALKUP SCREEN

03.TIMERS

Summary of Contents for e-studio 167





























































































































































































































Reviews:

No comments