manualshive.com logo in svg

Toshiba e-studio 167, Operator'S Manual For Copying Functions, Page: 4 / 220

Share
Download
Toshiba e-studio 167 Operator'S Manual For Copying Functions Download Page 4

2    Notice to Users

Notice to Users

For Germany only

After a suitable place has been selected for the installation of the e-STUDIO167/207/237, please do not 
change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide proper ventilation as 
the copier emits a small amount of ozone.

The unit is classified as Class 1 Laser Product according to IEC 60825-1:1993/EN 60825-1.1994 
including amendments.
The unit uses laser diode of output 5 mW, wave length 785 nm, continuous pulse.

Caution:

Use of controls or adjustments or performance of procedures other than those specified herein may 
result in hazardous radiation exposure.

Warning:

This is a Class A product. In a domestic environment this product may cause radio interference in which 
case the user may be required to take adequate measures.

Working environment

From EMC (Electromagnetic Compatibility) point of view, the operation of this product is being restricted 
in following environments: 

y

Medical Environments: This product is not certified as a medical product according to the Medical 
Product Directive 93/42/EEC.

y

Domestic environments (e.g. a private living room with TV / Radio sets in the nearby surrounding 
area) because this is a so called EMC class A product. In a domestic environment this product may 
cause radio interference in which case the user may be required to take adequate measures!

Any consequences resulting from the use of this product in restricted working environments are not the 
responsibility of TOSHIBA TEC.
The consequences of the use of this product in restricted working environments may be an electromag-
netic interference with other devices or machines in the nearby surrounding area. This can result into 
malfunction including data loss / data error pertaining to this product or the other devices / machines 
involved in the electromagnetic interference.
Furthermore, for general safety reasons, the use of this product in environments with explosive atmo-
spheres is not permitted.

CE compliance

This product is labelled with the CE mark in accordance with the provisions of the applicable European 
Directives, notably the Low Voltage Directive 2006/95/EC, the Electromagnetic Compatibility Directive 
2004/108/EC for this product and the electric accessories, the Radio Equipment and Telecommunica-
tions Terminal Equipment Directive 1999/5/EC for the telecommunication accessories.
CE marking is the responsibility of TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH, Carl-
Schurz-Str. 7, 41460 Neuss, Germany, phone +49-(0)-2131-1245-0.
For a copy of the related CE Declaration of Conformity, please contact your dealer or TOSHIBA TEC.

Machine Noise Information

Ordinance 3. GPSGV: The maximum sound pressure level is equal or less than 70 dB(A) according to 
EN ISO 7779

Summary of Contents for e-studio 167





























































































































































































































Reviews:

No comments