Toshiba e-studio 16 Operator'S Manual Download Page 161

Page: 161 / 207

4-65

Memory Transmission Report

This is the result report printed after a Memory Transmission. (A job transmitted after the document is
first scanned into memory.)

Auto Print (if programmed; (

see page 4-55.)

Printing will automatically start after a transmission is completed.

MEMORY TRANSMISSION REPORT

PAGE : 001

TIME : FEB-25-2001 11:48AM

TEL NUMBER : 12345678901234567890

E-MAIL : ABCDEFGHIJKLMNOPQRSTUVWXYZ12345678901234

NAME : ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEFGHIJKLMN

FILE NUMBER : 999

DATE : FEB-25 10:21AM

TO : ABCDEFGHIJKLMNOPQRST

DOCUMENT PAGES : 999

START TIME : FEB-25 10:00AM

END TIME : FEB-25 10:20AM

SENT PAGES : 995

STATUS : OK

FILE NUMBER : 004 *** SUCCESSFUL TX NOTICE ***

//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

image data

//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

File number of the memory transmission job (indicated in 3 digits (001 ~ 999))

Date and time when the memory transmission job was accepted

Remote party’s name or facsimile/telephone number

Number of pages input in memory

Time when the transmission started

Time when the transmission was completed (When the recovery transmission option is
ON, “(RECOVERY TIME: FEB-25 12:48PM)” is added. The data can be resent until the

time indicated after “Resend until: ” When the transmission is completed normally or the

recovery transmission option is OFF, this information is not added.)

Number of pages which were transmitted normally (indicated in 3 digits (001 ~ 999); more
than 1000 pages is printed as “999”.)

Result: (Result of communication: OK/NG)
The image data on page 1 is reduced and printed.

Summary of Contents for e-studio 16
















































































































































































































Search results

Summary of Contents for e-studio 16

Reviews:

Toshiba e-studio 16, Operator'S Manual, Page: 161 / 207

Search results

Summary of Contents for e-studio 16

Reviews: