Toshiba e-studio 16 Operator'S Manual Download Page 159

Page: 159 / 207

4-63

Mode (The communication mode and added function are indicated.)

EC 5 0 1 P

The communication mode is classified as shown below:

Communication Mode

Indication

ECM (*)

ECM

HW, HR

RDC communication

Result: The result of the transmission is indicated. If the transmission failed, an error

code is indicated. When a transmission was completed normally, nothing is

indicated.

NG 20

Error code
Result: OK (Successful)

NG (Failure)

(*): Toshiba shortened protocol version of the original mode is used.

Encoding method

0: MH

2: MMR

1: MR

3: JBIG

Resolution (pels/mm)

0: 8 × 3.85

4: 16 x 15.4

1: 8 × 7.7

8: 300 dpi

2: 8 × 15.4

Transmission speed (bps)

0: 2400

4: 12000

1: 4800

5: 14400

2: 7200

6: V.34

3: 9600

Communication mode

Special communication mode (P: Polling, R: Relay transmission)

Polling Communication

SR, R: Relay Communication
SB:

F-code Mailbox Communication

Sub Address Communication

PC-Fax Communication

Summary of Contents for e-studio 16
















































































































































































































Search results

Summary of Contents for e-studio 16

Reviews:

Toshiba e-studio 16, Operator'S Manual, Page: 159 / 207

Search results

Summary of Contents for e-studio 16

Reviews: