Toshiba B-EX6T Series Key Operation Specification Download

Page: 3 / 160

DISPLAY PATTERN AND KEY OPERATION FOR SYSTEM MODE ANDUSER SYSTEM MODE

................................................................................................................................................. 38

7.1

LIST BOX WITH SCROLLBAR .................................................................................................... 38

7.2

VALUE SETTING SCREEN ......................................................................................................... 41

7.3

INFORMATION SCREEN ............................................................................................................ 43

7.4

SENSOR ADJUSTMENT SCREEN ............................................................................................. 45

7.5

TEMPERATURE DISPLAY SCREEN.......................................................................................... 46

7.6

FILE SELECTION SCREEN ........................................................................................................ 47

INITIAL SETTING WIZARD (NOT AVAILABLE IN JA TYPE) .................................................. 48

SYSTEM MODE ....................................................................................................................... 51

9.1

OUTLINE OF THE SYSTEM MODE ............................................................................................ 51

9.2

REFLECTING THE SYSTEM MODE SETTINGS TO THE PRINTER ....................................... 52

9.3

RESET .......................................................................................................................................... 52

9.4

DIAGNOSTIC ............................................................................................................................... 52

9.4.1

MAINTENANCE COUNTER ......................................................................................................... 53

9.4.2

AUTO DIAGNOSTIC ..................................................................................................................... 75

9.4.3

HEAD CHECK ............................................................................................................................... 77

9.5

SET PARAMETERS ..................................................................................................................... 78

9.5.1

MEDIA LOAD ................................................................................................................................ 78

9.5.2

FEED KEY .................................................................................................................................... 79

9.5.3

MOVE TO TEAROFF .................................................................................................................... 79

9.5.4

FW/BK ACT. ................................................................................................................................. 80

9.5.5

RIBBON SAVE .............................................................................................................................. 80

9.5.6

HEAD UP CUT/RWD. ................................................................................................................... 80

9.5.7

PRE PEEL OFF ............................................................................................................................ 81

9.5.8

BACK FEED SPEED ..................................................................................................................... 81

9.5.9

AUTO HEAD CHECK.................................................................................................................... 81

9.5.10

RIBBON NEAR END ..................................................................................................................... 81

9.5.11

PAPER/RBN END ......................................................................................................................... 82

9.5.12

CALIBRATE .................................................................................................................................. 84

9.5.13

POWER SAVE TIME .................................................................................................................... 85

9.5.14

CODE PAGE ................................................................................................................................. 86

9.5.15

ZERO FONT ................................................................................................................................. 86

9.5.16

CTRL CODE ................................................................................................................................. 86

9.5.17

PEEL OFF STATUS ..................................................................................................................... 87

9.5.18

KANJI CODE ................................................................................................................................. 87

9.5.19

EURO CODE ................................................................................................................................ 87

9.5.20

MAXICODE SPEC ........................................................................................................................ 87

9.5.21

FEED ADJ. .................................................................................................................................... 88

9.5.22

CUT ADJ ....................................................................................................................................... 89

9.5.23

BACK ADJ. .................................................................................................................................... 92

9.5.24

X ADJUST ..................................................................................................................................... 93

9.5.25

HEAT ENERGY TYPE .................................................................................................................. 93

9.5.26

TONE ADJ. <T> ............................................................................................................................ 94

9.5.27

TONE ADJ. <D>............................................................................................................................ 95

9.5.28

RIBBON TORQUE ........................................................................................................................ 96

9.5.29

FRONT RIBBON MOTOR ............................................................................................................ 96

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands