Toshiba B-EX6T Series Key Operation Specification Download

Page: 52 / 160

9 SYSTEM MODE

9.1 OUTLINE OF THE SYSTEM MODE

1. The printer enters the system mode with the following operations.

・

While the printer power is off, perform either of the following operations:

・

Turn on the printer while holding down the [FEED] and [PAUSE] key at the same time.

・

Turn on the printer while holding down the [MODE] key.

・

While the printer is online, perform the following operation:

・

Hold down the [MODE] and [ENTER] keys at the same time for more than 3 seconds.

2. The system mode is intended for performing self-test and various parameter settings.

3. When the top menu is displayed, the main firmware version is shown on the right side of the title.

4. The language displayed on the LCD is Japanese when

“Japanese” is selected for the LCD language

parameter, and English when a language other than

“Japanese” is selected. (See <14>LCD PANEL.)

5. The key operations for the system mode are described below.

For the key functions and the display configuration, refer to Section

DISPLAY PATTERN AND KEY

OPERATION FOR SYSTEM MODE ANDUSER SYSTEM MODE.

Top menu of the system mode

Display

SYSTEM MODE

C1.6

▲

<1>DIAGNOSTIC

<3>TEST PRINT

▼

<0>RESET

<2>SET PARAMETERS

Top menu list

English

<0>RESET
<1>DIAG.
<2>SET PARAMETERS
<3>TEST PRINT
<4>SENSOR
<5>RAM CLEAR
<6>INTERFACE
<7>RFID
<8>RTC
<9>USB MEMORY
<10>FOR FACTORY
<11>BASIC
<12>Z-MODE
<13>XML
<14>LCD PANEL
<15>PASSWORD

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands