Toshiba B-EX6T Series Key Operation Specification Download

Page: 133 / 160

132

B-EX4T1

1. The maximum and minimum values vary depending on the module type.

Max. value

Min. value

Initial value

B-EX700-RFID-U2-EU/US-R

B-EX700-RFID-U4-R

B-EX700-RFID-U4-EU/US/AU-R

U4 module preinstall model

(B-EX4T1/T2-GS18/TS-18-CN-R)

2. The range of output level is 18 (approx. 100mW) to 0 (approx. 1mW).

3. The setting range of B-EX700-RFID-U2-EU / US-R is 9-18, but LCD displays 0-18.

4. If you set 0 to 8 out of the setting range in B-EX700-RFID-U2-EU/S-R, the operation is not guaranteed.

9.10.4.2 Q VALUE

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

Decimal

None

In the case multiple RFID tags are read at the same time, this menu is useful to focus on a target tag. Set the

Q value to

“1” or above (2 is recommended). Q value “0” causes the tags to interfere with each other and

disables proper data write.

When the Q value is set, set an AGC threshold for data write and an AGC threshold lower limit for retry, also.

Setting all these values enables writing data to a tag placed just above the antenna.

Actually, the problem of reading multiple tags at the same time does not occur with most RFID tag types. It is

not necessary to change the default setting of

“0”.

Note: This is effective only for the following modules:

B-EX6T1/T3

・

B-EX706-RFID-U4-R

・

B-EX706-RFID-U4-EU/US/AU-R

B-EX4T1

・

B-EX700-RFID-U2-EU/US-R

・

B-EX700-RFID-U4-R

・

B-EX700-RFID-U4-EU/US/AU-R

・

U4 module preinstall model (B-EX4T1/T2-GS18/TS18-CN-R)

9.10.4.3 AGC THRESHOLD

Max.

value

Min. value

Step

Display

Sign

Integer

digit

Decimal

place

0-padding

Unit of

measure

Decimal

None

When the obtained gain of an RFID tag is lower than the AGC threshold, the tag is considered as an error

tag even if a data write succeeds.

When the AGC threshold is set to

“0”, all tags are writable.

When this parameter is set to

“8”, for example, tags with the AGC threshold level of 7 or less are considered

as error tags.

The optimum value is different depending on the tag types.

Note: This is effective only for the following modules:

B-EX6T1/T3

・

B-EX706-RFID-U4-R

・

B-EX706-RFID-U4-EU/US/AU-R

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands