Toshiba B-EX6T Series Key Operation Specification Download

Page: 150 / 160

149

9.18.1.1 System mode and user system mode start screen when password is enabled

When the password is enabled, the password entry screen is displayed at the time the system mode or user
system mode is started.

Password entry for system mode

Display

Procedure

Turn on the printer while holding down the [FEED] and [RESTART] keys at
the same time.
The password entry screen is displayed.

Enter the password.

The printer enters the system mode.

When a wrong password is entered or the [CANCEL] key or [MODE] key is pressed

Password invalid message is displayed.

A wrong password was entered for 3 times consecutively.

The printer starts in online mode.

Password entry for user system mode

Note:
If you forgot the system mode password, disable it with @010 command

Display

Procedure

Turn on the printer, press the [PAUSE] key to place the printer in pause
state. Then, hold down the [MODE] key for 3 seconds.
The password entry screen is displayed.

Enter the password.

The printer enters the user system mode.

When a wrong password is entered or the [CANCEL] key or [MODE] key is pressed

Password invalid message is displayed.

A wrong password was entered for 3 times consecutively.

The printer locks. Turn off printer and back to on.

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands