Toshiba B-EX6T Series Page 128 Key Operation Specification Download

Page: 128 / 160

127

・

The number of tag being read/The total number of tags read

(Mostly, only 1 tag is read.)

・

For the UHF module, AGC value of the read tag is displayed with decimal number.

・

Data displayed on the 3rd and 4th lines are expressed with hex. code. (16 digits x 2 lines = 32 digits)

The displayed data differs depending on the module type.

B-EX6T1/T3

RFID module

Displayed data

B-EX706-RFID-U4-R

B-EX706-RFID-U4-EU/US/AU-R

EPC code of EPC area

B-EX4T1

RFID module

Displayed data

B-EX700-RFID-H1-QM-R

Tag ID

B-EX700-U2-EU/US-R

B-EX700-RFID-U4-R

B-EX700-RFID-U4-EU/US/AU-R

U4 module preinstall model

(B-EX4T1/EX4T2-GS18/TS18-CN-R)

EPC code of EPC area

・

In the case of 16 bytes or more data, only the first 16 bytes are displayed. When data is less than16

bytes, the vacant digits will be filled with spaces.

・

If more than one tag is read at one time, especially when short-pitch tags are used, pressing the [UP] or

[DOWN] key shows the other tags

’ data.

9.10.2 MODULE

The information related to the module setting is displayed.

The menu structure of MODLE

Menu item

<7>RFID

MODULE

MODULE TYPE

COUNTRY

TAG

RF CHANNEL

9.10.2.1 MODULE TYPE

B-EX6T1/T3

・

NONE

No RFID module is installed.

・

HF band(H1)

Not supported

・

HF band(H2)

Not supported

・

UHF band (U2/U4) B-EX706-RFID-U4-R (Japan)

B-EX706-RFID-U4-EU-R (Europe)

B-EX706-RFID-U4-US-R (U.S.A)

B-EX706-RFID-U4-AU-R (Australia)

B-EX4T1

・

NONE

No RFID module is installed.

・

HF band(H1)

B-EX700-RFID-H1-QM-R

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands