Toshiba B-EX6T Series Key Operation Specification Download | Manualshive

Page: 130 / 160

background image

129

*1: Selectable country codes differ depending on the RFID module type. Multiple country codes may be

displayed when setting a country code, but be sure to select the country where the RFID module is used.
Setting a different country code is prohibited.

For the selectable country codes, refer to Section 9.4.2.1 Module version and LCD message.

9.10.2.3 TAG

Selectable tag types vary according to the module setting.

The number in the table indicates the scroll line number.

NONE

H1

H2

U2/U4

NONE

1

1

1

1

I-Code

2

2

Tag-It

3

3

C220

4

4

ISO15693

5

5

2

C210

6

6

C240

7

7

C320

8

8

EPC C1 Gen2

9

2

9.10.2.4 RF CHANNEL

A channel used for RFID tag write is set.

・

AUTO

・

2CH

・

3CH

・

4CH

・

5CH

・

6CH

・

7CH

・

8CH

Notes:

1. When a channel is chosen from 2CH to 8CH, that channel will be continuously used.

2. When the channel is set to AUTO, an available channel is searched in the following order:

(2CH



8CH



6CH



4CH



3CH



7CH



5CH



2CH)

3. The channel setting works effectively only for the B-EX706-RFID-U4-R(*).

*: The frequencies used for the B-EX706-RFID-U4-R and B-EX700-RFID-U4-R are as follows.

Channel

2CH

3CH

4CH

5CH

6CH

7CH

8CH

Frequency (MHz)

921.0 921.2 921.4 921.6 921.8 922.0 922.2

«
...
128
129
130
131
132
...
»

Summary of Contents for B-EX6T Series

































































































































































Reviews:

No comments

Related manuals for B-EX6T Series

Brand: Datalogic Pages: 558

Brand: ID Tech Pages: 12

Brand: Vantec Pages: 7

ImageMate SDDR-88

Brand: SanDisk Pages: 63

Brand: bolid Pages: 9

SafezoneXID-500

Brand: LG CNS Pages: 33

00124153 MoveData

Brand: Hama Pages: 54

Brand: IDTECH Pages: 155

Brand: ArgoxScan Pages: 145

Brand: Lindy Pages: 60

Brand: HighSecLabs Pages: 14

C33-00-486000Z4

Brand: Datamax Pages: 10

Brand: Nordic ID Pages: 16

Brand: Nordic ID Pages: 22

Brand: Nordic ID Pages: 58

Brand: Supernote Pages: 78

Brand: Sonnet Pages: 2

Smart Card Reader

Brand: Wincor Nixdorf Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands