Toshiba B-EX6T Series Key Operation Specification Download

Page: 83 / 160

9.5.11 PAPER/RBN END

・

Stop immediately

When a label end or ribbon end status is detected, the printer stops immediately.

・

Complete current

When a label end or ribbon end status is detected, the printer prints the current label

as far as possible, then stops.

Notes:

1. Stop immediately:

When a label end or ribbon end is detected in the middle of printing, printing is immediately stopped.

When the printing is restarted, first the initial feed is performed, then the printer starts printing from the

unfinished label.

2. Complete current:

The

“Complete current” is valid only when the ribbon save function is set to OFF. Even when the ribbon

save function is enabled, the behavior of the

“Stop immediately” will be automatically performed

regardless of the setting. The printer behavior of the

“Complete current” at the detection of label end and

ribbon end is as follows.

(1) Label end detection



Printer behavior

When a label end is detected in the middle of printing, the printer completes the half-finished printing

and stops when the next label is at the home position, displaying the error message.

* Printing of the half-finished label is completed.



LCD message

“NO PAPER”



The remaining number of labels

[Specified number of labels]



[The number of finished labels at the time of printing stop (including the

half-finished label)]

If a label end is detected while the last one of the specified number of labels is printed, the remaining

number of labels on the LCD will be blank.



Printer behavior at restart

When the printing is restarted, first the initial feed is performed, then the printer starts printing from the

next label. In case the label end was detected while the last one of the specified number of labels was

printed, only the initial feed is performed, and if the status response has been set to ON, an issue end

status is sent after a feed end status.

Specified number of labels = 5, A label end is detected while the 3rd label is printed.

Printing: 1

label

… Finished (*)

Printing: 2

label ... Finished (*)

Printing: 3

label

… After an error is detected, printing of this label is completed. Finished (*)

Stop with error

… “NO PAPER” is displayed on the LCD.

Initial feed

… Restart

Printing: 4

label

… Finished (*)

Printing: 5

label

… Finished (*)

(*) Completely printed labels: 1

to 5

labels

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands