TiLite ZR Owner'S Manual Download

Page: 91 / 97

13-5

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 13: ANTI-TIPS

WARNING

The threads on the Allen screws that connect the Front Roller to the footrest tube are treated with Loctite

242

, a

medium strength thread lock. If you loosen either Allen screw, you MUST remove and reapply Loctite

242

or an

equivalent medium strength thread lock.

If you ignore this Warning, your front roller could fall off and you could fall, tip

over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Figure 13-7

Front Roller

Allen

Screws

Front

Roller

With an Angle Adjustable Footrest:

1. Remove the Allen screws that secure the Front Roller to the roller plate. See Figure 13-8.

2. Remove the Allen screws that secure the footplate and the clamp to the roller plate.

3. Reassemble the angle adjustable footplate as shown in Figure 3-6.

Note: If removing the Front Roller from an angle adjustable footrest, you will need to order new, shorter Allen screws

and washers to secure the footplate to the clamp.

Figure 13-8

Front Roller with Angle Adjustable Footplate

Locknuts

Allen Screws

Clamp

Roller Plate

Front

Roller

Allen Screws

Washers

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands