TiLite ZR Owner'S Manual Download

Page: 77 / 97

11-1

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 11: CASTERS And FORKS

Standard Forks

WARNING

Always mount identical size casters and forks on both sides of your chair.

If you ignore this Warning, you may fall, tip

over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Replacing Casters

Tools Needed:

• Two #2 Phillips Head Screw Drivers

1. Remove the two Phillips Head screws, C Spring washers and axle that secure the caster to the fork. Use one

screw driver to hold one screw in place and a second screw driver to loosen the other screw. See Figure 11-1.

2. Remove the caster and spacers from the fork.

3. Install the new caster, spacers and C Spring washers onto the fork and securely tighten the two screws so there

is no space between the caster, the spacers and the fork sides. Use one screw driver to hold one screw in place

and securely tighten the other screw with the second screw driver.

Note: If your chair has 4” or 5” TiLite Performance casters, make sure that Spacer 2 (which is wider than Spacer 1) is

positioned on the recessed side of the caster, which should be oriented outwards when the casters are in the trailing

position.

Caster Cap

Fork

Washer

Nylock Nut

Caster

Axle

Phillips

Head

Screw

Spacer 1

Phillips

Head Screw

Spacer 2

Figure 11-1

Bearing Fork

C Spring

Washer

C Spring Washer

“Bullet” Caster

Housing

Replacing Forks

Tools Needed:

• 9/16” Socket Wrench

WARNING

The ZR fork stem is permanently installed in the “Bullet” Caster Housing. Do not attempt to unscrew the fork stem

or the set screw. If it should become necessary to replace the fork stem on these chairs, this repair can only be

performed by TiLite at our factory.

If you ignore this Warning, you may fall, tip over or lose control of the wheelchair

and seriously injure yourself or others or damage the wheelchair.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands