TiLite ZR Owner'S Manual Download

Page: 84 / 97

12-2

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 12: REAR WHEELS

Handrims

WARNING

You must have your handrims replaced by an authorized TiLite dealer or qualified technician.

If you ignore this

Warning, you may seriously injure yourself or others or damage the wheelchair.

pneumatic Tires and Tubes

WARNING

Fully deflate the tire before performing any disassembly procedures. Do not re-inflate the tire until all re-assembly is

completed.

If you ignore this Warning, you may seriously injure yourself or others or damage the wheelchair.

Tools needed:

• #2 Phillips Screw Driver

• 3/8” Open End Wrench or 5/16” Open End Wrench

1. Remove the rear wheel from the chair.

2. Remove all air from the inner tube. If you have a Schrader valve (see Figure 12-3), remove valve stem cap and

release all of the air from the tube, by pressing down on the pin in the center of the valve stem. If you have a

Presta valve (see Figure 12-4), remove the valve stem cap, unscrew, counter clockwise, the knurled nut on the

valve stem and release all of the air from the tube by pressing down on the pin in the center of the valve stem.

3. Remove the tire and inner tube.

4. Make sure the rim strip is properly in place.

5. Install the new inner tube and tire onto the wheel.

6. Make sure the tire is properly seated in the wheel rim, and inflate the tire to the correct PSI rating on the sidewall

of the tire.

7. Reinstall the rear wheel on the chair.

Figure 12-3

Schrader Valve

Schrader

Valve

Figure 12-4

Schrader Valve

Presta Valve

Knurled Nut

Solid Tires

WARNING

Replacement of solid tires requires specialized equipment. Therefore, if your solid tires need replacement, you must

have this done by an authorized TiLite dealer or qualified technician.

If you ignore this Warning, you may seriously

injure yourself or others or damage the wheelchair.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands