TiLite ZR Owner'S Manual Download

Page: 54 / 97

6-4

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 6: SIDE GUARDS

Figure 6-5

Fendered Carbon Fiber Side Guard

Clamp

Side Guard

Mount

Stabilizer

Tab

Bracket

ADJUSTABLE FENDERED SIDE GUARD

(Aluminum)

Mounting

Tools Needed:

• 7/16” Open End Wrench

• 5/64” Allen Wrench

• 5/32” Allen Wrench

Note: You may need to adjust the Tension Adjustable by Strap Seat Sling to gain access to the seat tube hole. If this

is necessary, see “Adjusting the Tension” on pages 7-3 and 7-4.

1. Insert Allen Screw #1 through the conical washer, the slot in the rear cam, the spacer and into the

back mount. Do not tighten. See Figure 6-6.

2. Insert Allen Screw #2 through the conical washer, the slot in the front cam, coved washer, seat tube, saddle,

washer and the nylock nut. Do not tighten.

3. Loosen but do not remove the eight Button Head Cap screws (four in each cam).

4. Adjust the side guard to the desired position, rotating the cams as needed and allowing the Allen screws to slide

within the cam slots.

5. Once the desired side guard position has been achieved, tighten the eight Button Head Cap screws (four on each

cam) using the 5/64” Allen wrench.

6. Using the 5/32” Allen wrench, securely tighten Allen Screw #1.

7. Keeping Allen Screw #2 in place using the 5/32” Allen wrench, securely tighten the nylock nut using the 7/16”

Open End wrench.

WARNING

The threads on the Button Head Cap screws and Allen Screw #1 that secure the cams to the cam covers and the

sideguard to the back mount have been treated with Vibra-TITE® VC-3, a locking and sealing coating, to reduce the

possibility that they will become loose. You should be able to adjust the cams and/or sideguards approximately four

times without reapplying the coating to these screws. If you repeatedly adjust the cams or remove the sideguard,

TiLite requires that you reapply Vibra-TITE® VC-3 after every fourth adjustment.

If you ignore this Warning, you could

fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands