TiLite ZR Owner'S Manual Download

Page: 64 / 97

8-2

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 8: AXLE PLATES AND CAMBER PLUGS

(CENTER OF GRAVITY; REAR SEAT HEIGHT)

Replacing the Camber Tube

Tools Needed:

• 3/16” Allen Wrench

• 5/64” Allen Wrench

• Ruler

1. Remove the rear wheels.

2. Using the 5/64” Allen wrench, remove the bumper assembly, making note of the order in which the parts are

assembled.

3. Loosen, but do not remove, the Allen screw that secures the camber tube to each camber clamp. See Figure 8-2.

4. Remove the camber tube.

5. Install the new camber tube, making sure the distance from the outside edge of the camber clamp to the end of

the camber tube is identical on each side of the chair.

6. Make sure that the camber plug flats are perpendicular to the ground and that the camber is oriented properly.

7. Securely tighten both Allen screws.

8. Reinstall the bumper assembly.

9. Reinstall the rear wheels.

10. Check the toe-in/toe-out and adjust as needed. See pages 8-2 and 8-3.

Figure 8-2

Replacing the Camber Tube

Camber

Clamp

Camber Tube

Flats

Allen

Screw

Bumper

Assembly

Adjusting Toe-In/Toe-Out

Tools Needed:

• 3/16” Allen Wrench

• 7/8” Open End Wrench

• Ruler or Tape Measure

Note: Adjusting toe-in/toe-out does not apply to chairs with 0° camber; however, it is still necessary to make sure that

the camber plug flats are perpendicular to the ground.

1. Make sure the distance from the end of the camber tube to the camber clamp is identical on both sides of the

chair. See Figure 8-3.

2. Make sure the rear wheels are properly inflated.

3. Place the chair on all four wheels with the casters trailing toward the rear of the frame. See Figure 8-4.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands