TiLite ZR Owner'S Manual Download

Page: 32 / 97

2-2

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 2:

SAFETY INSPECTION, MAINTENANCE &

TROUBLESHOOTING

Inspection Item

Initially

Weekly

3 Months

Rear Tires

• Check for proper inflation as per sidewall of pneumatic tire

• Inspect for cracks, wear and flat spots

√

Camber Tube/Axle Sleeves

• Make sure camber plug clamps are securely tightened

• Make sure camber plugs are secure in camber plug clamps and

axle sleeves are secure in camber plugs

√

Handrims

• Inspect for signs of rough edges or peeling

• Make sure handrims are securely attached to rim

√

Wheel Locks

• Make sure wheel locks embed proper distance into tire and

prevents chair from moving when engaged

• Make sure wheel locks do not interfere with tire when disengaged

• Make sure pivot points are free of wear and looseness

√

Seat Sling and Back Upholstery

• Inspect for rips or sagging

• Inspect fastening flaps to ensure they are securely attached

• Inspect while seated to ensure sling supports your weight and does

not touch crosstubes

√

Casters/Forks

• Inspect wheels and tires for cracks and wear

• Inspect wheel/fork assembly for proper tension by spinning caster

(caster should come to a gradual stop); if caster wobbles, tighten

the axle

• Inspect wheel/fork assembly/stem bolt to ensure that stem bolt

is secure (wheel/fork assembly should not have excessive play

relative to the stem bolt but should rotate freely); if necessary,

tighten stem bolt

• Ensure that wheel bearings are clean and free from moisture

• If pneumatic, check for proper inflation as per the sidewall

√

Armrests

• Inspect to ensure that all hardware is securely attached

√

Footrests/Hangers

• Inspect to ensure that all hardware is securely attached

√

Anti-tips

• Inspect anti-tip wheel for cracks and wear

• Inspect to ensure that anti-tip receptacle is securely attached

√

Frame

• Inspect for cracks

√

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands