TiLite ZR Owner'S Manual Download

Page: 65 / 97

8-3

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 8: AXLE PLATES AND CAMBER PLUGS

(CENTER OF GRAVITY; REAR SEAT HEIGHT)

Figure 8-3

Adjusting the Toe-In/Toe-Out

Camber

Clamp

Camber

Tube

Measurement A

Figure 8-4

Adjusting the Toe-In/Toe-Out

4. Measure from the floor to the center of the axle (“Measurement A”). Be sure the tape measure/ruler is

perpendicular to the floor.

5. Block the wheels with a heavy object so the chair can not roll forward or backward (do not use the wheel locks as

this may affect the toe-in/toe-out adjustment).

6. Measuring from the floor at the rear of each tire, mark the tire (with a felt tip pen) at the same height as

Measurement A.

7. Measuring from the floor at the front of each tire, mark the tire (with a felt tip pen) at the same height as

Measurement A.

8. Measure the distance between the left and right tires at the rear reference marks made in Step 6. See Figure 8-5.

9. Measure the distance between the left and right tires at the front reference marks made in Step 7.

10. If the measurements in Steps 8 and 9 are the same (within 1/8”), no toeing adjustment is needed, and you may

skip to Step 13. If not, proceed to Step 11.

11. Loosen the Allen screw in each camber clamp that secures the camber tube in place.

12. If the measurement in Step 9 is less than the measurement in Step 8, rotate the camber tube using the 7/8” Open

End wrench rearward to toe-out the rear wheels. If the measurement in Step 9 is greater than the measurement

in Step 8, rotate the camber tube using the 7/8” Open End wrench forward to toe-in the rear wheels. Continue

adjusting the camber tube until these two measurements are equal. See Figure 8-6.

13. Securely tighten the Allen screws in the camber tube mount.
14. Square the casters to the floor.

Wrench

Figure 8-6

Adjusting the Toe-In/Toe-Out

Camber Plug

Camber

Tube

Figure 8-5

Adjusting the Toe-In/Toe-Out

Toe-In/Toe-Out

Measurement

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands