TiLite ZR Owner'S Manual Download

Page: 42 / 97

4-2

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 4: BACKRESTS And PUSH HAndLES

Changing the Backrest Angle

Tools Needed:

• 1/2” Open End Wrench

• 7/16” Open End Wrench

• 1/8” Allen Wrench

1. Lock the backrest in the unfolded position.

2. On both sides of the chair, using the Allen wrench, remove the Button Head cap screws and lock washers. See

Figure 4-3.

3. On both sides of the chair, using the Open End wrenches, loosen but do not remove the stop bolts and nylock

nuts.

4. Adjust the backrest to the desired angle. On one side of the chair, while holding the backrest in place, align one

of the five holes in the backrest cam with one of the three holes in the back mount. Place the Button Head Cap

screw through the lock washer, the backrest cam and into the back mount. Finger tighten. It may be necessary

to make a minor adjustment to the backrest angle in order to properly align the hole in the link with an available

threaded hole in the bracket. Once aligned, reinsert and finger tighten the Button Head cap screw removed in

Step 2 to securely attach the link to the backrest assembly.

5. Repeat Step 4 on the other side of the chair.

6. Securely tighten the Button Head cap screws, stop bolts and nylock nuts.

Figure 4-3

Changing the Backrest Angle

Nylock

Nut

Backrest

Back

Mount

Backrest

Cam

Lock Washer

Button Head

Cap Screw

Stop

Bolt

Adjusting the Backrest Height

Tools Needed:

• 5/32” Allen Wrench

Note: In order to adjust the backrest height, it is helpful to remove the backrest upholstery. Therefore, make a note

of the tautness of the backrest upholstery before removing it so you can reinstall it to approximately the same degree

of tautness.

1. Remove the backrest pad. See “Velcro

-Style Adjustable Back Upholstery” or “Tension Adjustable by Straps

Back Upholstery” on pages 7-1 to 7-3.

2. On both sides of the chair, remove the Allen screw that secures the backrest post inside the backrest. See Figure

4-4.

3. Reposition both backrest posts to the desired height inside the backrest, and reinsert and securely tighten the two

Allen screws.

4. Make sure both backrest posts are at the same height in the backrest.

5. Reinstall the backrest upholstery. See “Velcro

-Style Adjustable Back Upholstery” or “Tension Adjustable by

Straps Back Upholstery” on pages 7-1 to 7-3.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands