TiLite ZR Owner'S Manual Download

Page: 59 / 97

7-3

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 7:

BACK UPHOLSTERY, SEAT UPHOLSTERY AND SEAT

CUSHIONS

Replacing

1. Lift the back flap to expose the backrest ears. See Figure 7-5.

2. Completely detach the backrest ears and the strap(s) from the padded back and remove them from the backrest.

Note: If your chair has Integrated or Fold-Down Push Handles, you will need to remove the bolts that secure the

backrest ears to the backrest (using a 1/8” Allen wrench) and the bolts that secure the backrest posts inside the

backrest (using a 5/32” Allen wrench). See Figure 7-3 and see “Adjusting the Backrest Height” on page 4-2.

3. Remove the seat cushion.

4. Detach the bottom flap from the seat upholstery at the underside of the seat upholstery.

5. Attach the bottom flap of the new back upholstery to the seat upholstery at the underside of the seat upholstery

6. Install the new backrest ears on the backrest.

7. Adjust to the desired tautness. See “Adjusting the Tension” on page 7-2.

8. Align the top of the padded back with the backrest ears.

9. Reinstall the strap(s) and adjust to the desired tautness.

10. Securely attach the padded back to the backrest ears and lower the back flap back into position in front of the

rigidizer bar.

11. Replace the seat cushion.

Figure 7-5

Replacing

Padded Back

Back Flap

Backrest

Bottom Flap

Ear Straps

Backrest Ears

Corbac

Adjustable Contour Back Support

For information regarding the use and adjustment of the Corbac

Adjustable Contour Back Support, consult the

owner’s manual provided by the manufacturer, Ride Designs.

Tension Adjustable By Straps Seat Sling Upholstery

WARNING

Do not make the tension of the seat sling upholstery so loose that it does not properly support your weight. You

must never permit the sling to become so loose that your weight is borne by the crosstube below the seat sling. See

Figure 7-6.

If you ignore this Warning, you may develop pressure sores, which can be a life-threatening medical

complication.

Adjusting the Tension

1. Remove the seat cushion.

2. Detach the back upholstery from the seat upholstery (see “Velcro

-Style Adjustable Back Upholstery” on page 7-1

or “Tension Adjustable by Straps Back Upholstery” on pages 7-2 and 7-3).

3. Carefully tip the chair back until it is resting on its rear wheels and the backrest.

4. Detach one tension adjustable strap, adjust to the desired tension and refasten the strap. See Figure 7-6.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands