TiLite ZR Owner'S Manual Download

Page: 83 / 97

12-1

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 12: REAR WHEELS

WARNING

DO NOT attempt any of the procedures in this chapter if the chair is occupied.

If you ignore this Warning, serious

injury to the occupant will occur.

Quick-Release Axle

Removing

1. Hold the wheel securely at the hub. See Figure 12-1.

2. Depress the release button on the quick-Release Axle

and slide the wheel and axle out of the axle sleeve.

3. Release the release button.

Replacing

WARNING

Make sure the locking balls fully secure the quick-Release

Axle inside the axle sleeve before operating the chair.

you ignore this Warning, you may fall, tip over or lose

control of the wheelchair and seriously injure yourself or

others or damage the wheelchair.

1. Hold the wheel securely at the hub. See Figure 12-1.

2. Depress the release button on the quick-Release Axle,

making sure the locking balls recess into the axle.

3. Insert the axle all the way into the axle sleeve.

4. Release the release button.

5. Pull firmly on the wheel (without depressing the release

button) to make sure the wheel is locked securely in place.

Quad Quick-Release Axle

Removing

1. Unlock the lever on the quad quick-Release Axle.

See Figure 12-2.

2. Slide wheel and axle out of the axle sleeve.

Replacing

WARNING

Make sure the locking balls fully secure the quad quick-

Release Axle inside the axle sleeve before operating the

chair.

If you ignore this Warning, you may fall, tip over or

lose control of the wheelchair and seriously injure yourself

or others or damage the wheelchair.

1. Hold the wheel securely at the hub. See Figure 12-2.

2. Unlock the lever on the quad quick-Release Axle,

making sure the locking balls recess into the axle.

3. Insert the axle all the way into axle sleeve.

4. Lock the lever on the quad quick-Release Axle.

5. Pull firmly on the wheel (without unlocking the lever) to

make sure the wheel is locked securely in place.

Figure 12-1

Removing and Replacing the Rear Wheel

with the Quick-Release Axle

Release

Button

Hub

Axle

Figure 12-2

Removing and Replacing the Rear Wheel

with the Quad Quick-Release Axle

Release

Lever

(locked)

Hub

Axle

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands