TiLite ZR Owner'S Manual Download

Page: 63 / 97

8-1

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 8: AXLE PLATES AND CAMBER PLUGS

(CENTER OF GRAVITY; REAR SEAT HEIGHT)

All TiLite rigid wheelchairs are equipped with a camber tube. By adjusting the position of the camber tube, you can

adjust the center of gravity of your chair. In some cases, you also can adjust the rear seat height. This chapter

explains the various adjustments that are possible. The same adjustment will apply whether you have an aluminum,

titanium or carbon fiber camber tube and regardless of the degree of camber.

WARNING

Any changes to the position of the camber tube will affect the stability of the chair. Use extreme caution when using a

new camber tube position as the new position may make the chair more prone to tip over.

If you ignore this Warning,

your chair may not perform properly, which in turn, may cause you to fall, tip over or lose control of the chair and

seriously injure yourself or others or damage the chair.

WARNING

Whenever you adjust the position of the camber tube (either to adjust the rear seat height or the center of gravity), it

may be necessary to adjust the toe-in/toe out of the rear wheels. See “Adjusting Toe-In/Toe-Out” on pages 8-2 and

8-3. In addition, whenever you adjust the position of the camber tube or when you adjust the toe-in/toe-out, it may be

necessary to square the casters to the floor.

If you ignore this Warning, your chair may not perform properly, which,

in turn, may cause you to fall, tip over or lose control of the chair and seriously injure yourself or others or damage the

chair.

Note: It is recommended that you remove the rear wheels and turn the chair upside down before attempting to make

any adjustments described in this chapter.

Standard Camber Mounts

Adjusting the Center of Gravity

WARNING

When repositioning the camber clamps on the CG Brackets, always leave as many open holes between the two Allen

screws as your desired placement will permit. NEVER use two adjacent holes to attach the camber clamps to the CG

Brackets.

If you ignore this Warning, your camber clamp may fail, causing you to fall, tip over or lose control of the

chair and seriously injure yourself or others or damage the chair.

Tools Needed:

• 5/32” Allen Wrench

1. Remove the rear wheels.

2. Remove the four Allen screws (two on each side) that

secure the camber clamps to the CG brackets. See

Figure 8-1.

3. Reposition the camber clamps to the desired position

on the CG Brackets, making sure the positioning is

identical on both sides of the chair. You MUST leave

one open hole between the two Allen screws.

4. Reinstall the Allen screws and lock washers and

securely tighten all four Allen screws.

5. Reinstall the rear wheels.

6. Check the toe-in/toe-out and adjust as needed. See

pages 8-2 and 8-3.

Figure 8-1

Adjusting the Center of Gravity

CG Bracket

Camber Clamp

Washers

Allen Screws

Open Hole

(Required)

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands