TiLite ZR Owner'S Manual Download

Page: 51 / 97

6-1

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 6: SIDE GUARDS

Cloth Side Guards

Removing/Replacing

1. Lift up on the seat cushion and remove it from the chair.

2. Separate the Cloth Side Guards from the seat upholstery and the back upholstery. See Figure 6-1.

3. If desired, install new Cloth Side Guards onto the seat and back upholstery.

Note: The fastening flaps that secure the Cloth Side Guards to the back upholstery wrap around the outside of

the back canes and under the back upholstery flap.

4. Replace the seat cushion.

Cloth

Side

Guard

Figure 6-1

Removing/Replacing

Back Upholstry

Flap

Back Cane

Fastening

Flaps

Rigid Removable and Quad Removable Side Guards

(Aluminum and Carbon Fiber)

Using Rigid Side Guards

To remove either type of Rigid Side Guard, lift the side guard out of the side guard mount by grasping it at the top or

place finger in the hole and pull it upward. See Figure 6-2. To replace, place the bracket into the slot between the

side guard mount and the clamp and push down.

Figure 6-2

Rigid Side Guards

Clamp

Side Guard

Mount

Bracket

quad Removable

Side Guard

Rigid Removable

Side Guard

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands