TiLite ZR Owner'S Manual Download

Page: 53 / 97

6-3

ZR Owner’s Manual

OM_ZR_0913RevA

CHAPTER 6: SIDE GUARDS

Fold-Down Rigid Side Guards

(Aluminum and Carbon Fiber)

Using Fold-Down Side Guards

To fold down, simply remove the seat cushion and push the top of the side guard toward the seat sling. To unfold,

simply pull the side guard up away from the seat sling. See Figure 6-4.

Figure 6-4

Fold-Down Side Guards

Allen

Screws

Clamp

Dowel

Washers

Removing

Tools Needed:

• 3/16” Allen Wrench

1. Remove the two Allen screws that secure the two halves of the side guard clamp. See Figure 6-4.

2. Remove the Fold-Down Side Guard clamp assembly.

Reinstalling

Tools Needed:

• 3/16” Allen Wrench

1. Align the two halves of the side guard clamp around the seat tube of the frame. See Figure 6-4.

Note: The half of the side guard clamp to which the side guard mount is attached has a dowel pin protruding from

the clamp that must be inserted in the side guard clamp hole in the frame.

2. Insert the two Allen screws through the washers and the two halves of the clamp and securely tighten.

Fendered Carbon Fiber Side Guard

Using Fendered Side Guards

To remove the Fendered Side Guard, lift the side guard out of the side guard mount. To replace, place the bracket

into the slot between the side guard mount and the clamp. Make sure the rearward end of the side guard is inside the

stabilizer tab. See Figure 6-5.

To adjust the fendered side guards, see “Adjusting” on page 6-2.

Summary of Contents for ZR


































































































Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands

TiLite ZR, Owner'S Manual

Search results

Summary of Contents for ZR

Reviews:

Related manuals for ZR

Brands by name

Popular brands