If the front left/right speakers are to be crossed over, set the front left/right crossover frequencies and slopes for all 3
crossover types (buttons
2
,
3
and
4
) all to the same values. Please refer to page 50 for details.
After the front left/right speakers have been configured, press
SETUP
once to return to the
SETUP
/
INPUT
/
SPEAKER
CONFIGURATION
sub menu, and press button #
2
(
CENTER
) to configure the center
speaker. The
CENTER
CONFIGURATION
sub menu is shown in figure 80.
Center Speaker Configuration
This submenu of settings is exactly the same as the one for the front left/right speakers, but applies only for the
center speaker. All of the same guidelines and procedures apply except for the case where no center speaker is
present, and where the low pass signal (if the center speaker is crossed over) can be routed to. If no center speaker
is present in the system, the
CONFIG
parameter should be set to
PHANTOM
. With this setting, the signal for the
center channel is routed to the front left/right speakers.
Pressing button #
1
allows the configuration of the center speaker. If
this speaker is not to be crossed over, nor any of its signal sent to the
SUB
output, then this should be set to
FULL RANGE
. There is an
option where the full range signal can be routed to the center speaker
and a low pass part of it routed to the sub as discussed above. If this is
desired, the
CONFIG
setting should be
FULL W/LOP
. (A crossover
type must be selected, and the appropriate crossover frequencies and
slopes set up). The center speaker can be crossed over and instead of
its low pass portion going to the SUB output, it can be routed to the
front left/right speakers. In this case, the
CONFIG
parameter would be
set to
XOVER L/R
. The center speaker can also be set to
OFF
or
CROSSOVER
.
Figure 80 - Video Display of the SETUP/INPUT page 1/SPEAKER CONFIG/ CENTER Sub Menu
If a fifth
SUB
DAC channel is installed and enabled in the Casablanca III, the low pass portion of the center signal
will be routed to this output unless the
CONFIG
parameter is set to
XOVER L/R
. Otherwise the low pass portion of
the center channel will be routed to the front
SUB
output(s), or
SUB
output if there is only one
SUB
enabled.
Press button #
2
,
3
and
4
to set up the crossover settings for the center speaker in the same manner as with the
front left/right. The crossover sub menus are the same with the exception of the speaker name in the upper right
corner of the VFD.
Pressing button #
5
allows the user to select the crossover type that will be applicable for the center speaker only.
Button #
6
allows the user to adjust the level of center channel information that is mixed with the front left/right
channels, if the
CONFIG
parameter is set to
PHANTOM
.
Press
SETUP
twice to return to the speaker configuration sub menu, then press button #
3
(
SURROUNDS
) to set up
the surround speakers. This submenu is shown in figure 81.
86
Summary of Contents for Casablanca III
