Speaker Levels
This sub menu allows the user to set the relative level of each speaker in order to reflect the audio system speaker
configuration, room characteristics, or the listener’s preference. The allowable relative range is
-15dB to +15dB. The
BALANCE
function (discussed later) allows the user to temporarily adjust the Left/Right and
Front/Rear balances, and the Center & Sub channel levels to compensate for differences in program material or
source.
The level sub menu(s) are completely interactive with the DAC channels that are installed into the Casablanca III. An
example of this is: If there are 6 DAC channels installed, the names of these channels will be displayed on one page
of the levels sub menu. If more than 6 DAC channels are installed, first a menu will appear asking the user which set
of speakers are to have their levels adjusted:
1-6
or
7-12
, as shown in figure 33. In both of these sub menus, the
installed and configured DAC channel, or speaker names will be displayed.
Figure 33 - Front Panel Display of the SETUP
/
INP
/
LVLS/Channel Choice Sub Menu
From an Input Select menu, press
SETUP
, input (
INP
) then levels (
LVLS
) to access the speaker levels setup sub
menu shown in figure 34. Again, if more than 6 DAC channels are installed, the user must press either button #
1
(
1-
6
) or #
2
(
7-12
) first.
Figure 34 - Front Panel Display of the SETUP
/
INP
/
LVLS 1-6 Sub Menu
If there are more than 6 DAC channels installed, pressing button #
2
on the Levels channel choice submenu will
produce a second levels sub menu similar to the one shown in figure 35. The speaker names in this sub menu may
not match the user’s Casablanca III if the same DAC channels are not installed and configured.
Figure 35 - Front Panel Display of the SETUP
/
INP
/
LVLS 7-12 Sub Menu
In these submenus, press button(s)
1
-
6
to select a speaker to edit. Use the
LEVEL UP
/
DOWN
buttons to adjust each
speaker’s output level. If there is a level control on the sub itself, adjust that first and then fine tune with the
Casablanca III.
Internal Noise Generator
To aid in establishing a desired system speaker level balance, the Casablanca III provides the user with the option of
either routing the currently selected audio signal to the outputs, or routing an internally generated noise signal to either
the currently selected speaker or to all speakers simultaneously.
This function is accessed via the
A-D
button in the
SETUP
/
INP
/
LVLS
sub menu(s). Press buttons
1
-
6
to select a
speaker. Pressing the
A-D
button repeatedly toggles through these sources. Table 5 shows the 3 possible routings.
55
Summary of Contents for Casablanca III
