indicates that the name in the VFD is to be edited. VFD names are limited to 4 characters. Press the
LEVEL
UP
/
DOWN
button to change characters and the
LEVEL LEFT
/
RIGHT
to change character positions. Pressing the
DISPLAY
button once will clear the current
INPUT SELECT
name. Press the
A-D
button to edit the OSD name.
OSD
will appear in the lower portion of the display. This name can be up to 15 characters and the current character
to be edited will blink on screen.
Press
SETUP
once to return to the
SETUP
/
INP
page 3
submenu.
Master Delay
When video processing occurs, there can sometimes be a delay in the output of the video signal. Each process may
be only 1 to 2 frames out of sync, however, each can add up to a significant enough amount to where the audio and
video are not in sync. If this happens, the Casablanca III allows the user to set an overall, or master delay on all
outputs simultaneously in order to re-sync the audio with the video signal. In the
SETUP
/
ACTIVE INPUT SETTINGS
page 3
submenu, press button #
2
and use the
LEVEL UP
/
DOWN
buttons to adjust the audio delay time until the
video appears to be in sync with the audio. The range is
0
to
100
mS at 48KHz.
When complete, press
SETUP
twice to return to the
INPUT SELECT
menu.
Password for Each INPUT SELECT Button
Press button #
3
to set a password for the currently selected input. Entering a password here will prompt the user to
type in the password each time he/she wishes to change configuration settings for this
INPUT
SELECT
.
When the
PW
button is pressed, an “
ARE YOU SURE YOU WANT TO ENTER A PASSWORD FOR THIS MENU?
”
message appears on the screen. Pressing
NO
(button #
6
) reverts back to the
SETUP
/
INP
Page 3
submenu.
Pressing
YES
(
A-D
button) will display a screen that allows a password to be entered, with the first character
blinking. The user can use buttons
1
-
6
to enter a password, or elect to have no password for this
INPUT SELECT
button by pressing the
A-D
button 5 times, which will display all zeros, indicating no password.
Note
: If a zero appears in any position of the password, it will be seen as all zeros, or no password.
PLEASE
REMEMBER and/or WRITE DOWN YOUR PASSWORD!
If it is forgotten, all access to password protected areas
will be denied! Please refer to page 14 for additional information on using passwords.
Center Spread
This parameter adjusts the mix between the center speaker and the front left/right speakers. This effect is a post
process to all other digital signal processing and is therefore activated in the
POST PROCESS
sub menu. The
higher the value, set in
SETUP
/
ACTIVE
INPUT
SETTINGS
/
page 3
, the more center level is reduced in the center
speaker and added into the front left/right speakers. If the value were at its highest, all of the center speaker
information would be routed to the front left/right speakers. In this case, it would be the same as phantoming the
center speaker.
96
Summary of Contents for Casablanca III
