Thermo Scientific 42iQD Instruction Manual Download Page 91

Page: 91 / 286

Operation

Settings

Thermo Scientific

42iQD Instruction Manual

3-67

The Status and Renewal Request screen allows the user to access the iQ360

menu once the subscription has been enabled.

Home Screen>Settings>Health Check>iQ360>Status and Renewal

Request

The Status and Renewal Request screen contains the following

information:

●

iQ360 Status:

Informs the user if the subscription is enabled.

●

iQ360 Subscription Expiration Date:

Informs the user when the

subscription will expire.

●

iQ360 Test Connection:

Allows the user to verify the network

connection is working.

●

iQ360 Subscription Renewal:

Allows the user to request a subscription

renewal via email.

Status and

Renewal

Request

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands