Thermo Scientific 42iQD Instruction Manual Download Page 83

Page: 83 / 286

Operation

Settings

Thermo Scientific

42iQD Instruction Manual

3-59

The Maintenance screen reminds the user when certain instrument

components need to be serviced/replaced.

Note

This symbol denotes there is an active maintenance alarm in the

module.

▲

Home Screen>Settings>Health Check>Maintenance

Home Screen>Settings>Health Check>Maintenance>Advanced

Maintenance

The Maintenance screen contains the following information:

●

Preventive Maintenance:

Shows suggested service interval and time left

for component replacement.

●

Change Part:

User logs component fix.

●

Maintenance History:

Shows the log of all recorded component fixes.

●

Service Tips:

Provides video and procedural service tips.

●

Advanced Maintenance:

Resets all preventive maintenance items.

Maintenance

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands