Thermo Scientific 42iQD Instruction Manual Download Page 152

Page: 152 / 286

Operation

Settings

3-128

42iQD Instruction Manual

Thermo Scientific

The Update Bootloader screen allows the user to update bootloader and

reboot the instrument. The bootloader is a small program that interfaces

with our hardware and runs our operating system on power-up. The

bootloader may change to optimize hardware settings or if there are

changes to the hardware. If the button is blue, an update to the bootloader

is available. If button is greyed out, no update is needed.

Home Screen>Settings>Update Bootloader

The Update Bootloader screen contains the following information:

●

Reboot and Update:

Update bootloader and reboot instrument.

●

Exit:

Exits screen.

Update Bootloader

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands