manualshive.com logo in svg

Thermo Scientific 42iQD, Instruction Manual

Share
Download
Thermo Scientific 42iQD Instruction Manual Download Page 223

Servicing 

DMC PMT Cooler and Reaction Chamber Replacement 

Thermo Scientific 

42iQD Instruction Manual     

7-33

 

 

Use the following to replace the photomultiplier tube (PMT). 
Equipment Required: 

Screwdriver, flat head 
Phillips drive, #2 

1.

 

Turn the instrument OFF, unplug the power cord, and remove the 

cover (

Figure 2–1

). 

2.

 

Unplug electrical connections PMT (J7) and HVPS (J4). 

 

Figure 7–37.

 PMT Tube Replace-Elec-Pt1 

3.

 

Using a flat head screwdriver, wedge out of top right corner starting 

point, labeled 1 (

Figure 7–38

). 

4.

 

Continue to wedge out the four midpoints of the plate to remove the 

snap on access panel, labeled 2 (

Figure 7–39

). 

Photomultiplier 

Tube (PMT) 

Replacement 

Summary of Contents for 42iQD































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands