manualshive.com logo in svg

Thermo Scientific 42iQD, Instruction Manual

Share
Download
Thermo Scientific 42iQD Instruction Manual Download Page 230

Servicing 

DMC Ozonator 

7-40

     42iQD Instruction Manual 

Thermo Scientific 

 

Use the following procedure to replace the ozonator and transformer board, 

and to replace the flow switch. 

●

 

Removing the ozonator and transformer 

●

 

Replacing the ozonator and transformer board 

●

 

Replacing the flow switch 

Use the following procedure to remove the ozonator and transformer. 
Equipment Required: 

Phillips drive, #2 

1.

 

Turn the instrument OFF, unplug the power cord, and remove the 

cover (

Figure 2–1

). 

2.

 

Unplug converter DMC (J2) and flow pressure board (J4). 

 

Figure 7–44.

 HVPS, Electrical 

DMC Ozonator 

Ozonator and 

Transformer 

Removal 

Summary of Contents for 42iQD































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands