manualshive.com logo in svg

Thermo Scientific 42iQD, Instruction Manual

Share
Download
Thermo Scientific 42iQD Instruction Manual Download Page 216

Servicing 

DMC PMT Cooler and Reaction Chamber Replacement 

7-26

     42iQD Instruction Manual 

Thermo Scientific 

 

Use the following procedure to replace the PMT cooler and clean or 

replace the reaction chamber assembly. 

●

 

Remove the PMT Cooler 

●

 

Replacing the PMT board 

●

 

Removing and Cleaning the Reaction chamber 

●

 

Replacing the PMT Cooler and Reaction chamber 

●

 

PMT Replacement 

Use the following procedure to remove the PMT cooler from the 

instrument. 
Equipment Required: 

Phillips drive, #2 

1.

 

Turn the instrument OFF, unplug the power cord, and remove the 

cover (

Figure 2–1

). 

Make sure the PMT has cooled down before touching. 

▲

  

 

2.

 

Unhook plumbing by pulling loop downwards and unhook tubing. 

3.

 

Using a #2 Phillips drive, unfasten two 6-32 flat head screws. 

4.

 

Pull shroud outwards. 

DMC PMT Cooler 

and Reaction 

Chamber 

Replacement 

PMT Cooler Shroud 

Removal 

Icon Here 

Summary of Contents for 42iQD































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands