Thermo Scientific 42iQD Instruction Manual Download Page 87

Page: 87 / 286

Operation

Settings

Thermo Scientific

42iQD Instruction Manual

3-63

The Maintenance History screen allows the user to view when components

are replaced, rebuilt, or cleaned. When a user changes a part in the change

part screen, the new row will be automatically created at the top in the

maintenance history table.
Use the



and



buttons to move up and down and the



and



buttons to move left and right.

Home Screen>Settings>Health Check>Maintenance>Maintenance

History

Note

Retrieving maintenance history data, it may take a few seconds...

▲

The Maintenance History screen contains the following information:

●

Part:

Component that has been fixed.

●

Fix:

The type of maintenance.

●

Date:

Shows date/time when service was logged.

●

Service Months:

Amount of time in months since last service.

●

Comments:

Shows comments entered from time of change.

Maintenance History

Summary of Contents for 42iQD































































































































































































































































































Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQD, Instruction Manual

Search results

Summary of Contents for 42iQD

Reviews:

Brands by name

Popular brands