manualshive.com logo in svg

Thermo Scientific 42iQD, Instruction Manual

Share
Download
Thermo Scientific 42iQD Instruction Manual Download Page 68

Operation 

Settings 

3-44

     42iQD Instruction Manual 

Thermo Scientific 

 

The Ozonator screen provides status and alarms related to the ozonator 

module. If an item being monitored goes outside the lower or higher alarm 

limit, an alarm is activated. 
Use the 

 and 

 buttons to move up and down and the 

 and 

 

buttons to move left and right. 

Home Screen>Settings>Health Check>Status and Alarms>Ozonator

 

 

The Ozonator screen contains the following information: 

●

 

Across: 

●

 

Ozonator:

 This column lists items associated with the ozonator. 

●

 

Value:

 Displays the current value for each item. 

●

 

Low Alarm:

 Displays low alarm status for each item. 

●

 

High Alarm:

 Displays high alarm status for each item. 

●

 

Units:

 Displays units for each item. 

●

 

Down: 

●

 

Ozonator Power:

 Displays the current ozonator power on or off. 

●

 

Ozonator Level:

 Displays the current ozonator level. 

●

 

Ozonator Flow:

 Displays OK/Fail for ozonator flow. 

●

 

Ozonator Current:

 Displays the current ozonator Current. 

●

 

Board Communication:

 Displays OK/Fail for board communication 

status. 

●

 

Power Supply:

 Displays OK/Fail of power supplies. Power supply 

goes red if any voltages are outside their limits. No voltage rows 

ever get highlighted. 

Ozonator 

Summary of Contents for 42iQD































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands