![background image](http://html1.mh-extra.com/html/thermo-king/slx-spectrum/slx-spectrum_manual_1104415008.webp)
6
FIRST AID AND SAFETY
SAFETY PRECAUTIONS
Thermo King recommends all services be
performed by a Thermo King dealer. However,
there are several general safety practices which
you should be aware of:
1. Always wear safety glasses when working
with or around the refrigeration system or
battery.
Refrigerant or battery acid can cause
permanent damage if it comes in contact
with your eyes.
2. Never operate the unit with the compressor
discharge valve closed.
3. Always keep your hands and loose clothing
clear of fans and belts when unit is running
or when opening or closing compressor
service valves.
4. Always use extreme caution if you ever have
occasion to drill holes in your unit. This
could weaken structural components.
Drilling into electrical wiring or refrigerant
lines could cause a fire.
5. All service work on evaporator or condenser
coils be completed by a certified Thermo
King technician. If you ever do have
occasion to be working around the coils, use
extreme caution as exposed coil fins could
cause painful lacerations.
AUTO START/STOP OPERATION
This unit may start up at any time without prior
warning.
CYCLE-SENTRY
If your unit is equipped for CYCLE-SENTRY
operation, the unit may start automatically at
any time when the unit is turned on and the
CYCLE-SENTRY is selected.
ELECTRIC STANDBY
On Model 50 units, the unit may start
automatically at any time when the unit is
switched on, connected to live electric power
and/or the Electric operation is selected.
Be sure to switch the unit off before opening
the doors or inspecting any part of the unit.
ELECTRICAL HAZARD
Units with electric operation
or
electric standby
present a potential electrical hazard. Always
disconnect the high voltage power cable before
working on the unit.
WARNING!
A battery can be dangerous. A battery
contains a flammable gas that can ignite or
explode. A battery stores enough electricity
to burn you if it discharges quickly. A
battery contains battery acid that can burn
you. Always wear goggles or safety glasses
and personal protective equipment when
working with a battery. If you get battery
acid on you, immediately flush it with water
and medical attention.
WARNING!
Electric welding generates high amperage
currents which can damage electrical and
electronic components. To minimize
damage, prior to any welding operation on
the vehicle, the microprocessor and unit
battery must be electrically disconnected
from the vehicle. Switch the Microprocessor
On/Off switch to Off. Remove the negative
battery cable. Remove all connectors from
the rear of the microprocessor. Close the
control box. Connect the welder ground
cable as close as possible to the area being
welded. When welding is completed,
remove the welder ground cable. Reconnect
the cables to the rear of the
microprocessor. Reattach the negative
battery cable. Switch the microprocessor
On/Off switch to On. Reset all alarms and
codes to previous settings. Run a full
Pretrip. A detailed procedure may be found
in Thermo King Service Procedure A26A.
Summary of Contents for SLX SPECTRUM
