Texas Instruments OMAP-L137 EVM User Manual Download Page 204

Page: 204 / 222

OMAP-L137

SPRS563G – SEPTEMBER 2008 – REVISED JUNE 2014

www.ti.com

Table 6-112. DSP Debug Features

Category

Hardware Feature

Availability

Software breakpoint

Unlimited

Up to 10 HWBPs, including:

4 precise

(1)

HWBPs inside DSP core and one of them is

Basic Debug

associated with a counter.

Hardware breakpoint

2 imprecise

(1)

HWBPs from AET.

4 imprecise

(1)

HWBPs from AET which are shared for

watch point.

Up to 4 watch points, which are shared with HWBPs,

Watch point

and can also be used as 2 watch points with data (32

bits)

Watch point with Data

Up to 2, Which can also be used as 4 watch points.

Analysis

Counters/timers

1x64-bits (cycle only) + 2x32-bits (watermark counters)

External Event Trigger In

External Event Trigger Out

(1)

Precise hardware breakpoints will halt the processor immediately prior to the execution of the selected instruction. Imprecise breakpoints
will halt the processor some number of cycles after the selected instruction depending on device conditions.

ARM:

•

Basic Debug
–

Execution Control

–

System Visibility

•

Advanced Debug
–

Global Start

–

Global Stop

•

Advanced System Control
–

Subsystem reset via debug

–

Peripheral notification of debug events

–

Cache-coherent debug accesses

•

Program Trace
–

Program flow corruption

–

Code coverage

–

Path coverage

–

Thread/interrupt synchronization problems

•

Data Trace
–

Memory corruption

•

Timing Trace
–

Profiling

•

Analysis Actions
–

Stop program execution

–

Control trace streams

–

Generate debug interrupt

–

Benchmarking with counters

–

External trigger generation

–

Debug state machine state transition

–

Combinational and Sequential event generation

204

Peripheral Information and Electrical Specifications

Submit Documentation Feedback

Product Folder Links:

OMAP-L137

Summary of Contents for OMAP-L137 EVM































































































































































































































Search results

Summary of Contents for OMAP-L137 EVM

Reviews:

Related manuals for OMAP-L137 EVM

Brands by name

Popular brands

Texas Instruments OMAP-L137 EVM, User Manual

Search results

Summary of Contents for OMAP-L137 EVM

Reviews:

Related manuals for OMAP-L137 EVM

Brands by name

Popular brands