Texas Instruments OMAP-L137 EVM User Manual Download Page 100

Page: 100 / 222

OMAP-L137

SPRS563G – SEPTEMBER 2008 – REVISED JUNE 2014

www.ti.com

6.11.3 EMIFB Electrical Data/Timing

Table 6-28. EMIFB SDRAM Interface Timing Requirements

CVDD = 1.3 V

(1)

CVDD = 1.2V

(2)

NO.

MIN

MAX

MIN

MAX

Input setup time, read data valid on EMB_D[31:0] before

(DV-CLKH)

0.59

0.8

EMB_CLK rising

Input hold time, read data valid on EMB_D[31:0] after

h(CLKH-DIV)

1.25

1.5

EMB_CLK rising

(1)

Commercial (default), Industrial and Extended temperature range rated devices for 456 MHz max CPU operating frequency as
applicable to the device

(2)

Commercial (default), Industrial, Extended and Automotive temperature range rated devices for 400/375/300/266/200 MHz max CPU
operating frequencies as applicable to the device

Table 6-29. EMIFB SDRAM Interface Switching Characteristics for Commercial (Default) Temperature

Range

CVDD = 1.3 V

(1)

CVDD = 1.2V

(2)

NO.

PARAMETER

MIN

MAX

MIN

MAX

c(CLK)

Cycle time, EMIF clock EMB_CLK

6.579

7.5

w(CLK)

Pulse width, EMIF clock EMB_CLK high or low

2.63

d(CLKH-CSV)

Delay time, EMB_CLK rising to EMB_CS[0] valid

4.25

5.1

oh(CLKH-CSIV)

Output hold time, EMB_CLK rising to EMB_CS[0] invalid

1.1

d(CLKH-DQMV)

Delay time, EMB_CLK rising to EMB_WE_DQM[3:0] valid

4.25

5.1

Output hold time, EMB_CLK rising to

oh(CLKH-DQMIV)

1.1

EMB_WE_DQM[3:0] invalid

Delay time, EMB_CLK rising to EMB_A[12:0] and

d(CLKH-AV)

4.25

5.1

EMB_BA[1:0] valid

Output hold time, EMB_CLK rising to EMB_A[12:0] and

oh(CLKH-AIV)

1.1

EMB_BA[1:0] invalid

d(CLKH-DV)

Delay time, EMB_CLK rising to EMB_D[31:0] valid

4.25

5.1

Output hold time, EMB_CLK rising to EMB_D[31:0]

oh(CLKH-DIV)

1.1

invalid

d(CLKH-RASV)

Delay time, EMB_CLK rising to EMB_RAS valid

4.25

5.1

oh(CLKH-RASIV)

Output hold time, EMB_CLK rising to EMB_RAS invalid

1.1

d(CLKH-CASV)

Delay time, EMB_CLK rising to EMB_CAS valid

4.25

5.1

oh(CLKH-CASIV)

Output hold time, EMB_CLK rising to EMB_CAS invalid

1.1

d(CLKH-WEV)

Delay time, EMB_CLK rising to EMB_WE valid

4.25

5.1

oh(CLKH-WEIV)

Output hold time, EMB_CLK rising to EMB_WE invalid

1.1

dis(CLKH-DHZ)

Delay time, EMB_CLK rising to EMB_D[31:0] tri-stated

4.25

5.1

Output hold time, EMB_CLK rising to EMB_D[31:0]

(CLKH-DLZ)

1.1

driving

(1)

Commercial (default) temperature range rated devices for 456 MHz max CPU operating frequency as applicable to the device

(2)

Commercial (default) temperature range rated devices for 400/375/300/266/200 MHz max CPU operating frequencies as applicable to
the device

100

Peripheral Information and Electrical Specifications

Submit Documentation Feedback

Product Folder Links:

OMAP-L137

Summary of Contents for OMAP-L137 EVM































































































































































































































Search results

Summary of Contents for OMAP-L137 EVM

Reviews:

Related manuals for OMAP-L137 EVM

Brands by name

Popular brands

Texas Instruments OMAP-L137 EVM, User Manual

Search results

Summary of Contents for OMAP-L137 EVM

Reviews:

Related manuals for OMAP-L137 EVM

Brands by name

Popular brands