Terasic TR-5 Lite FPGA User Manual Download

Page: 69 / 86

TR5-Lite User Manual

www.terasic.com

June 20, 2018

ignore the functionality of the transceiver controller in the demonstration.

For CDMC61004 programming, users must trigger the CLK_RST_n to notify the chip to perform

PLL recalibration. For Si570 programming, please note the device I2C address is 0x00. Also, before

configure the output frequency, users must to Freeze the DCO (bit 4 of Register 137) first. After

configure the output frequency, users must Un-freeze the DCO and assert the NewFreq bit (bit 7 of



Design Tools



Quartus II 11.1 SP2



Nios II Eclipse 11.1 SP2



Demonstration Source Code



Quartus II Project directory: Nios_BASIC_DEMO



Nios II Eclipse: Nios_BASIC_DEMO\Software



Nios II IDE Project Compilation



Before you attempt to compile the reference design under Nios II Eclipse, make sure the project

is cleaned first by clicking on ‘Clean’ in the ‘Project’ menu of Nios II Eclipse.



Demonstration Batch File

Demo Batch File Folder:

Nios_BASIC_DEMO\demo_batch

The demo batch file includes following files:



Batch File for USB-Blaster (II): test.bat, test_bashrc (test_ub2.bat, test_bashrc_ub2)



FPGA Configure File: TR5_LITE_gondlen_top

.sof



Nios II Program: Nios_DEMO

.elf



Demonstration Setup



Make sure Quartus II and Nios II are installed on your PC.

Summary of Contents for TR-5 Lite FPGA























































































Search results

Summary of Contents for TR-5 Lite FPGA

Reviews:

Related manuals for TR-5 Lite FPGA

Brands by name

Popular brands

Terasic TR-5 Lite FPGA, User Manual

Search results

Summary of Contents for TR-5 Lite FPGA

Reviews:

Related manuals for TR-5 Lite FPGA

Brands by name

Popular brands