background image

vi 

PRISM Field Upgrade Kit Instructions 

 

Japan Compliance Statement 

 

 
Important Safety Information 

 

This manual contains information and warnings that must be followed by the user for 

safe operation and to keep the product in a safe condition.  

To safely perform service on this product, see the Service safety summary that follows 

the General safety summary.  

 

General Safety Summary  

Use the product only as specified. Review the following safety precautions to avoid 

injury and prevent damage to this product or any products connected to it. Carefully read 

all instructions. Retain these instructions for future reference.  

 

Comply with local and national safety codes.  

For correct and safe operation of the product, it is essential that you follow generally 

accepted safety procedures in addition to the safety precautions specified in this manual.  

 

The product is designed to be used by trained personnel only.  

Only qualified personnel who are aware of the hazards involved should remove the cover 

for repair, maintenance, or adjustment.  

Before use, always check the product with a known source to be sure it is operating 

correctly.  

 

While using this product, you may need to access other parts of a larger system. Read the 

safety sections of the other component manuals for warnings and cautions related to 

operating the system.  

 

When incorporating this equipment into a system, the safety of that system is the 

responsibility of the assembler of the system.  

 

To Avoid Fire or Personal Injury  

Use proper power cord:

 Use only the power cord specified for this product and certified 

for the country of use. Do not use the provided power cord for other products.  

 

Ground the product:

 This product is grounded through the grounding conductor of the 

power cord. To avoid electric shock, the grounding conductor must be connected to earth 

ground. Before making connections to the input or output terminals of the product, 

ensure that the product is properly grounded. Do not disable the power cord grounding 

connection.  

Summary of Contents for PRISM MPI-UP PHY-12G









































Reviews: